鑄造裂紋

   　 （1）鋼錠缺點惹起的鑄造裂紋  大片面鋼錠缺點，鑄造時都大概造成開裂，圖片6-8所示為2Cr13主軸鍛件中間裂紋。這是因?yàn)樵?t鋼錠凝集時結晶溫度局限窄，線壓縮系數大。冷凝補縮不足，表里溫差大，軸心拉應力大，沿枝晶開裂，造成鋼錠軸心晶間裂紋，該裂紋在鑄造時進一步擴大而成主軸鍛件中已裂紋。

  　 該缺點可經歷下列措施予以消除：①進步冶煉鋼水純潔度；②鑄錠遲鈍冷卻，削減熱應力；③接納*的發燒劑與保溫帽，增大補縮才氣；④接納中間壓實鑄造工藝。

 　 （2）鋼中有害雜質沿晶界析出惹起的鑄造裂紋  鋼中的硫常以FeS形式沿晶界析出，其熔點僅有982℃，在1200℃鑄造溫度下，晶界上FeS將發生融化，并以液態薄膜形式困繞晶粒，破壞晶粒間的結合而產生熱脆，輕微鍛擊就會開裂。

    鋼中含銅在1100～1200℃溫度下的過氧化性氣氛中加熱時，由于選定性氧化，上層會造成富銅區，當跨越銅在奧氏體中溶解度時，銅則以液態薄膜形式漫衍于晶界，造成銅脆，不行鑄造成形。要是鋼中還存在有錫、銻還會緊張低落銅在奧氏體中的溶解度，加劇這種脆化傾向。

　   （3）異相（第二相）惹起的鑄造裂紋  鋼中第二相的力學性能往往和金屬基體有很大的差別，于是在變形流動時會惹起附加應力導致整體工藝塑性下降，一旦部分應力跨越異相與基體間結合力時，則發生分別辨別造成孔洞。例如鋼中的氧化物、氮化物、碳化物、硼化物、硫化物、硅酸鹽等等。假設這些相呈密集。鏈狀漫衍，尤其在沿晶界結合力微弱處存在，高溫鍛壓就會開裂。圖片6-10是20SiMn鋼 87t錠因微細的 AlN沿晶界析出惹起鑄造開裂的宏觀形貌，其表面曾經氧化，出現多面體柱狀晶。微觀說明評釋，鑄造開裂與微細的顆粒狀A(yù)lN沿一次晶晶界大量析出有關。

  　 對策是：

　    1）限制鋼中加鋁量，去除鋼中氮?dú)饣蛴眉逾伔ㄒ种艫lN析出量；

 　   2）接納熱送鋼錠，過冷相變處理工藝；

　    3）進步熱送溫度（＞900℃）干脆加熱鑄造；

　    4）鍛進步行充分的勻稱化退火，使晶界析出相分散。

　    6.過熱、過燒與溫度不均

  　  加熱溫度過高或高溫停頓光陰過長時易惹起過熱、過燒。過熱使質料的塑性與打擊韌性顯著低落。過燒時質料的晶界劇烈氧化大概融化，*落空變形才氣。

    當加熱溫度漫衍緊張不勻稱，闡揚為鍛坯表里、正背面、沿長度溫差過大，在鑄造時惹起不均變形，偏心鑄造等缺點，亦稱欠熱。

   　 對策是：

　    l）嚴酷實行正確的加熱規范；

　    2）留意裝爐方法，防止部分加熱；

 　   3）調準測溫儀表，經心加熱操縱，控制爐溫、爐氣流動，防止不勻稱加熱。

自由鍛件廠商哪家好，就找唐山盛通鍛造有限公司。

Casting crack

   (1) Casting cracks caused by the defects of steel ingots The disadvantages of large-section steel ingots are probably caused by cracking during casting. Figures 6-8 show the intermediate cracks of 2Cr13 spindle forgings. This is because the crystallization temperature is narrow and the line compression coefficient is large when the 6t steel ingot is agglomerated. Insufficient condensation and shrinkage, large temperature difference in the surface, large axial tensile stress, cracking along the dendrites, causing intergranular cracks in the ingot axis, which is further enlarged during casting to become cracked in the spindle forging.

  This shortcoming can be eliminated by the following measures: 1 improving the purity of molten steel; 2 ingot cooling, reducing thermal stress; 3 receiving superior heat-generating agent and thermal insulation cap, increasing the feeding capacity; 4 receiving the intermediate compact casting process.

 (2) The sulfur in the cast cracked steel caused by the precipitation of harmful impurities along the grain boundary in steel often precipitates along the grain boundary in the form of FeS. Its melting point is only 982 °C. At the casting temperature of 1200 °C, FeS will melt on the grain boundary. And the film is trapped in the form of a liquid film, destroying the bond between the grains to produce hot brittleness, and slight forging will crack.

    When the copper in the steel is heated in a peroxidizing atmosphere at a temperature of 1100 to 1200 ° C, the upper layer causes a copper-rich region due to selective oxidation. When the solubility in copper is in the austenite, the copper is in the form of a liquid film. It is distributed in the grain boundary, causing copper to be brittle and not casting. If there are tin and antimony in the steel, the solubility of copper in the austenite will be weakened, which will aggravate this embrittlement tendency.

(3) The mechanical properties of the second phase in the cast cracked steel caused by the heterogeneous (second phase) tend to be very different from that of the metal matrix, so that additional stress will be caused during the deformation flow, resulting in a decrease in the overall process plasticity. When the bonding force between the heterogeneous phase and the substrate is crossed, the holes are separately identified. For example, oxides, nitrides, carbides, borides, sulfides, silicates, and the like in steel. Assume that these phases are dense. Chain-like diffusion, especially in the weak adhesion along the grain boundary, high temperature forging will crack. Figure 6-10 shows the macroscopic morphology of the 87t ingot of the 20SiMn steel due to the precipitation of fine AlN along the grain boundary. The surface is once oxidized and polyhedral columnar crystals appear. According to the microscopic explanation, the casting cracking is related to the precipitation of fine granular AlN along the primary crystal grain boundary.

  The countermeasures are:

1) limiting the amount of aluminum added to the steel, removing nitrogen from the steel or suppressing the precipitation of AlN by adding titanium;

 2) Accepting hot-sending steel ingots, supercooled phase change treatment process;

3) Progressive hot delivery temperature (>900 ° C) simply heating casting;

4) Forging into the foot and fully aligning the annealing to disperse the grain boundary precipitation phase.

6. Overheating, overheating and uneven temperature

  If the heating temperature is too high or the high temperature is too long, it will easily cause overheating and overheating. Overheating significantly reduces the plasticity and impact toughness of the material. During the over-burning, the grain boundary of the material is violently oxidized and melted, and it is completely emptied and deformed.

    When the heating temperature is uneven, it is said that the forging billet is in the front, the back, the temperature difference is too large, causing uneven deformation during casting, eccentric casting and other shortcomings, also known as underheating.

   The countermeasures are:

l) Strictly implement the correct heating specifications;

2) Pay attention to the furnace charging method to prevent partial heating;

 3) Adjust the temperature measuring instrument, control the temperature of the furnace and the flow of the furnace gas to prevent uneven heating.